Automated multistoried car parking system

  1. Introduction
  2. Basic idea
  3. Hardware description
    1. Display section
    2. Keyboard, Indicator & Beeper section
    3. Lift & motor section
    4. Sensor section
    5. LCD section
  4. Software program


Automatic multistoried car parking system helps to minimize the car parking area. In the modern world, where parking-space has become a very big problem and in the era of miniaturization, it is become a very crucial necessity to avoid the wastage of space in modern, big companies and apartments etc. In places where more than 100 cars need to be parked, this system proves to be useful in reducing wastage of space. This Automatic Car Parking System enables the parking of vehicles, floor after floor and thus reducing the space used. Here any number of cars can be parked according to the requirement. This makes the system modernized and even a space-saving one. This idea is developed using 8051 Microcontroller. Here program is written according to this idea using 8051.

Photograph of the model
Photograph of the model

2. Basic idea:

A display is provided at the ground floor which is basically a counter that displays number of cars in each floor. It informs whether the floors are fully filled with the cars or is it having place in a particular floor or not. There is facility of lift to carry the car to up and down. Movement of Lift is controlled by stepper motor. An indicator with a green and red LED is kept in all the floors to indicate whether the lift is busy or is it ready to take the car up or down. If the red LED glows that means the lift is already engaged and the person has to wait for the green LED to glow. In this project we have provided three floors of a building for car parking. Maximum storage capacity of each floor is given as ten. Storage capacity can be changed according to the requirement.

Any one can enter to first or second floor. The third floor in this model is for VIP’s only. Therefore when VIP’s are to be entering they are expected to enter their password and they will be taken to the third reserved floor. The password will be of 4 digits. The processor checks for the password entered and if it is found to be wrong, a siren is heard. In this particular model 10 passwords are stored. So when a password is entered, the processor checks for it and it is compared with 10 passwords. It indicates whether it is the correct one or not.

When the car enters the lift, the LDR detects its presence and sends a signal to glow RED LED indicating that the lift is busy. It also sends a signal to motor which makes the motor to rotate. After RED LED glows the lift will take the person and the car up to the floor where the space for parking is available. (For VIP it will be the third floor). When the lift reaches the first floor, the processor compares  the filled amount to that of the already fed capacity of that floor, and if it finds that the first floor is fully filled , it goes to the second floor and thus the procedure stops here. As soon as a car is placed in a particular floor, the display counter at the ground floor increments as to indicate the floor capacity has decreased by one. After the lift places the car in a particular floor, it comes back to its normal position and that time, the motor that drives it , also stops. Now processor sends signal to glow GREEN LED indicating that lift is free.

When a person needs to come down from a particular floor to ground floor, he is expected to focus the headlight onto the LDR placed in that floor. Now sensor section sends signal to motor that the lift has to be send back to that particular floor and sends a signal to glow RED LED indicating that the lift is busy. As soon as the lift reaches that particular floor car should come inside the lift, the display counter at the ground floor decrements by one as to indicate the floor capacity has increased by one. Lift comes back to its normal position and that time, the motor that drives it, also stops. Now processor sends signal to glow GREEN LED indicating that lift is free.

If there no parking taking place, the processor carries out the job according to the following priority:-

  1. It checks whether any password is entered.
  2. It checks whether any car is entered to lift.
  3. It checks whether any car headlight is pressed in front of  LDR placed in each floor.

It is like a round robin system.

3. Hardware description:

Introduction to 8051 Microcontroller:

The first task faced when learning to use a new computer is to become familiar with the capability of the machine. The features of the computer best learned by studying the internal hardware design, also called the architecture of the device, to determine the type, number, and size of the registers and other circuitry.

The hardware is manipulated by an accompanying set of program instructions, or software. One familiar with hardware and software, the system designer can then apply the microcontroller to the problems at hand. In this project we make use of microcontroller.

The 8051 microcontroller generic part number actually includes a whole family of microcontrollers that have numbers ranging from 8031 to 8751.The block diagram of the 8051 shows all of the features unique to microcontrollers:

  1. Internal ROM and RAM
  2. I/O ports with programmable pins
  3. Timers and counters
  4. Serial data communication

The block diagram also shows the usual CPU components program counter, ALU, working registers, and the clock circuits.

The 8051 architecture consists of these specific features:

  1. 8 bit CPU with registers A and B
  2. 16 bit PC &data pointer (DPTR)
  3. 8 bit program status word (PSW)
  4. 8 bit stack pointer(SP)
  5. Internal ROM or EPROM (8751)of 0(8031)to 4k(8051)
  6. Internal RAM of 128 bytes.
  7. 4 register banks , each containing 8 registers
  8. 80 bits of general purpose data memory
  9. 32 input/output pins arranged as four 8 bit ports:P0-P3
  10. Two 16 bit timer/counters:T0-T1
  11. Two external and three internal interrupt sources
  12. Oscillator and clock circuits

A pin out of the 8051 packaged in a 40 pin DIP is shown below.

Internal block diagram of IC 8051
Internal block diagram of IC 8051
A pin out of the 8051 packaged in a 40 pin DIP.
A pin out of the 8051 packaged in a 40 pin DIP.
Editorial Team
Editorial Team

We are a group of young techies trying to provide the best study material for all Electronic and Computer science students. We are publishing Microcontroller projects, Basic Electronics, Digital Electronics, Computer projects and also c/c++, java programs.

403 thoughts on “Automated multistoried car parking system

  1. sir
    i am doing this project .can you mail the pcb layout of this project with all inter connection and its complete circuit diagram.
    sir,it will help me more,plz mail me as soon as possible.

  2. Im interested in this project could u plizzz send me the full schematic,circuit diagram and coding or flow chart plizzzzz its urgent

  3. can you plz mail me the details of this project with circuit diagram…i want to make this on as my major project,plz mail me as soon as possible

  4. sir can you please send me the circuit diagram of this project. it will be very helpful for us.
    thank u in advance…..

  5. Sir, Im interested in this project could u plz mail me the complete circuit diagram of the project?

  6. Plz send me full circuit diagram plz I do this project in final year. Plz help me sir. & all students

  7. Sir, I am a B.E. student and I want to do this project as my final yr project. So i want the complete ckt diagram of this project. I request you to please send me at my email address as early as possible.

  8. Dear sir ,
    i’m very interested on this project , can you send me the full details of this nice project ?
    Very appreciate 🙂

  9. dear sir, I am also intersted in doing this project, bt i hv ltl confusion, that when a car comes near to ground floor then wheather the user is inside or not, also if at any floor there are 2 cars alerady parked and next car has to be park then how the car will go from lift to that perticular space. Again if when any user wants to go and needs his car back then how his car will get back to perticular person. According to this project it is applicable only for the single car.

  10. SIR,
    I am the student of B E final yr , in intrested your project . but i have some problem in this project, so please send me circute dig and flow chart, coding please sir its urgant, please send as soon as possible.
    Thanks a lot.

  11. I am sty diploma final year sir this project all detills hear. but circuit diagram not pll help me…… pll Response me

  12. sir , i m final year student and i want to make multilevel car parking system as my minor project but i have some difficulty in programing pllzz help me..

  13. How we know that parking space is available or not I.e if in each floor their is capacity of park 10 car then how we know that 10 cars are parked or not??

Leave a Reply

Your email address will not be published. Required fields are marked *

Get the latest updates on your inbox

Be the first to receive the latest updates from Codesdoc by signing up to our email subscription.