Water level indicator and controller
Generally overhead tanks are filled with water by operating a pump. We have no control over the level to which it may be filled. It may cause overflow or water level may remain too low when we switch OFF the pump motor. Manual operation of the motor pump starter is thus not advisable. Present circuit may be added to the existing manual starter of the pump motor so that it may be operated automatically.
Four sensor probes made up of brass or stainless steel stiff wires or rods may be hung firmly in the tank. This indicates the water level in the water tank at four steps F, H, L, E i.e., Full, Half, Low, Empty. When there is no water in the water tank the circuit automatically switches ON the pump and switches OFF when the water level comes to Full.
Probes marked E and L are hung with their bottoms near the bottom level of the tank at which we wish to start the pump. The probe F is hung with its bottom end in between those probes E and F. It is used for indication of the middle level.
Sensor H, L, F are connected with resistors R1, R2, and R3, where as probe E is directly connected to ground. Resistors R1, R2, R3 are connected to 12V supply through resistors R4, R5 and R6 respectively.
Working:
When the water level in the tank is below probes E and L, output of gate N9 is logic low and output of gate N12 is latched to logic high level. Simultaneously output of gate N11 goes logic low and is inverted by inverter. Now the output of gate N10 becomes logical high, and thus the transistor is forward biased to ON state and the relay is energized. These results in shorting of power supply contact to the pump and thus switching ON the pump motor.
As the water starts filling in the tank and ultimately touches probe F, the output of gate N11 goes high and is inverted by inverter. Now the output of gate N10 becomes logical low, and thus the transistor is reverse biased to OFF state and the relay is de-energized. These results in opening of power supply contact to the pump and thus switching OFF the pump motor.
Water level states are displayed using IC 5 and IC 6 in conjunction with 7-segment display. The display indicates F for Full, H for Half, L for Low and E for Empty level condition.
Can you please send me the details of this project?
can u please send me the pcb drawing for each circuits fast pleaaaaaaaaaaaaase I neeeeeeeeed them???????
al-marsa87@hotmail.com
please mail the details to m_awan89@hotmail.com
hi,
i am interested in electronics house.so plz send me the related details of this projects.
nice project
I want to make it as a final year of my university project.pls send me details like circuit diagram, description, requirements,budget n physical view. pls my id: safayeth.bd@hotmail.com
plssssssssssssssssss
this is awesome project.please send me all pcb lay outs,circuit diagrams,lay out of circuits on house.functionong of remote controlled equipments.pls send me the full details about this project..thankuuuuu……my email id:rajeshkannapwf@gmail.com
I HAD FINISHED ALL THE BREAD BOARD CONNECTION ON THIS PROJECT, NOW I HAD TO PROCEED TOWARDS PCB DESIGN SO PLEASE SEND ME THE LAYOUT ON THIS PROJECT………..
SO PLEASE HELP ME MA EMAIL ID :punya_chettri@yahoo.com
Respected Person,
I am very intersted in smart house.
Please send me all detail related to smart house as soon as possible.
I shall be very thankful to you.
—mohit
sir,
i just want more abut electronic house concept
please relay on me,i want to make it my profession
sir,
i just want more abut electronic house concept
please send me this project . this is essential in now-days……..
Dear Sir,
I am so glad that I come across your site as I was looking for similar projects. It is very informative.
Please let me know if you have the layout and pcb details and if possible please mail the same to me to my above email. I will be ever grateful to you for that.
Thanks and warm regards,
Sushil Rao
hi, friend
this project is simply superb.iam very interested to know all details of the project.please send me the details please——–
bye.
i think i interested to do electronic house project…please send me as soon as possible about the details of this project including the circuit and the pic programming..thank you..
sir..
i’m really intrested in this project..hope u can mail me the whole details about this project ASAP..im very thankful if you give me a hand…
regards..
sir..
i’m willing to do this project..hope u can mail me the whole details about this project ASAP..im very thankful if you give me a hand…
regards..
Dear sir,
I am interested in ELECTRONIC HOUSE.please send circuit detail and more information…
pls……send me all information
hi.sir now i am in final year. i want to do this project sir.please send me the details about this project sir.i need layout,circuit diagram and all details to implement this project sir.please sir,send every details to me sir.
I saw this dude, he was wearing a leather jacket, and at the same time he was eating a hamburger and drinking a glass of milk. I said to him “Dude, you’re a cow. The metamorphosis is complete. Don’t fall asleep or I’ll tip you over.”
I am a student of b.tech(EC) final year
I’m interested in this project.
Can you please send me all the details and circuit diagram of this project with component list with its spacification.
I am a student of b.tech(EC) final year
I’m interested in this project.
Can you please send me all the details and circuit diagram of this project with component list with its spacification.
I am BCA 2year student from vinayaka mission university.
Please you can sent some C++ project,code.
anilvishwkrmabca@gmail.com
hi..
plz send me d details…
hi
You project is the best
Can you please send me all the details and circuit diagram of this project with component list with its spacification. I really need it for my final year project.
HI.
SIR.
i am be final year student i interested in this project please send detail of this project and also pcb layout for same.
I HOPE YOU SEND SOON.
THANKS SIR
DEAR SIR,
you have done a wonderful job. Please let me know if you have the layout and pcb details and if possible please mail the same to me on above mail.
thanx
How would it be possible to start the motor between specific hours of the day. As you know in city , power supply is available for a certain fix hours . I would like to have some idea from upon this.
*Water supply